- Elay Plastic
- 17 October 2026
FIBC Seam Leakage: How to Specify Sift-Resistant Bags for Fine Powders
A bag may have intact fabric and neat stitching yet still allow a fine powder to escape. For a buyer, the useful question is where the product is leaving the package: through the woven body, along a sewn joint, or around an inlet, outlet or liner closure. Each route calls for a different specification review.
This guide focuses on product sifting at FIBC seams. It complements our guide to inner liners and coated fabric by explaining how to describe the leakage problem, define the seams that need attention and evaluate a proposed construction with the actual product.
1. Treat “sift-proof” as a construction description
Sift-resistant construction is intended to reduce the escape of fine material. A common approach combines coated fabric with filler cord in the sew lines. The cord is incorporated into the seam to help obstruct paths through which dust or powder could escape.
The commercial term “sift-proof” should still be connected to a clear requirement. Ask what construction is proposed, which seams receive the treatment and how its performance will be evaluated. The name alone does not establish a universal zero-leakage result for every powder.
2. Locate the escape route before changing the bag
Document where residue first appears and when it becomes visible. Separate observations during filling, after closing, after approved handling and at receipt. Photograph the area before cleaning, identify the bag batch and record whether the same pattern occurs on several bags.
Check whether the residue originates at the package or was deposited during filling. Powder on the outside of a bag is not, by itself, proof that a side seam has failed. Keeping these observations separate helps the supplier investigate the relevant part of the design.
3. Include more than the vertical body seams
Specify the areas to be reviewed on the drawing: body joints, bottom attachment, filling-spout attachment and discharge-spout attachment, where present. A circular woven body removes the vertical side seams, but it does not remove the other sewn connections in the finished FIBC.
Ask the manufacturer to identify the seam treatment and its extent. Do not rely on a phrase such as “dustproof sewing” without an agreed construction. Changes to the bag or stitching should be reviewed by the manufacturer as part of the complete design.
4. Distinguish fabric coating, seam treatment and a liner
Coating addresses the woven fabric surface. Sift-resistant sewing addresses the sewn joints. An inner liner creates a separate containment layer, whose suitability also depends on its construction, condition and closure. These are related features, rather than interchangeable names for the same solution.
Some powders can be packed using a suitable sift-resistant outer construction; others may need an appropriate liner. Select the combination with the supplier using the product and process information. If a liner is proposed, confirm how it fits the bag and how its inlet and outlet will be closed. See our FIBC inner liner options.
5. Describe the powder and the filling process
Provide the product name, available particle-size distribution and any known variation between batches. A description such as “mineral powder” leaves important questions unanswered. Include bulk density, target net weight, filling method, product temperature and the current bag specification.
Explain whether the issue occurs consistently or only on a particular line, product batch or delivery route. If possible, send photographs and a reference sample through an agreed sampling process. Avoid assigning a universal particle-size cutoff at which every bag will start to leak; the full product and package need evaluation.
6. Agree a representative sample evaluation
Before a bulk order, agree the proposed design, trial quantity, observation points and acceptance criteria. Use the intended product and the facility's approved filling, closing and handling procedures. Record the sample identification, filled weight, closure method and any liner details so the result can be traced to the tested configuration.
Inspect the identified leakage points at each agreed stage. Record the location and extent of any residue using a consistent method agreed by buyer and supplier. A clean bag immediately after filling does not, on its own, establish performance after storage or transport.
Keep containment evaluation alongside the other purchasing requirements. The bag still needs the specified load capability and any applicable product-specific requirements. Our guides to electrostatic FIBC classifications and food and pharmaceutical requirements cover separate specification questions.
What to include in a sift-resistant FIBC inquiry
| Information | What to provide | Why it helps |
|---|---|---|
| Packed product | Name, particle-size data and available product reference | Defines the material to be contained. |
| Load and dimensions | Net weight, required SWL, bulk density and bag dimensions | Connects containment to the complete bag specification. |
| Leakage observations | Photographs, locations, timing and bag batch | Directs attention to the actual escape route. |
| Current construction | Fabric, coating, seams, liner and closures | Provides a reference for comparing proposed changes. |
| Operating conditions | Filling method, temperature and handling/storage route | Helps define a representative sample evaluation. |
| Acceptance and supply | Agreed containment criteria, quantity and destination | Aligns technical approval with the quotation. |
Frequently asked questions
Does coated fabric automatically mean sift-resistant seams?
No. Confirm the seam construction separately; coating the body fabric does not describe every sewn joint.
Does every fine powder require a liner?
No single construction suits all powders. Evaluate the proposed bag and any liner with the actual product and intended process.
Does a circular FIBC have no seams?
A circular body eliminates vertical side seams, while other attachments in the finished bag may still be sewn.
Can a seam photograph replace a filling trial?
A photograph helps identify the construction or problem location. It does not demonstrate containment throughout the intended use.
Discuss your powder-containment requirement
Review our standard FIBC bags and filling and discharge guide. Complete the FIBC specification form with the available product data, then contact Elay Plastic or email bigbag@elayplastic.com to discuss the proposed construction and sample evaluation.